Accton Router Login
Access your Accton router at 192.168.1.1 or 192.168.2.1. Complete login guide with default credentials (root/none), configuration steps for Cheetah Access and all Accton router models.
What is Accton Router Login?
Accton router login provides access to your router's web-based admin interface at 192.168.1.1 or 192.168.2.1 (Cheetah Access). Default username is root with password none (blank). Accton manufactures enterprise-grade networking equipment with advanced management features.
Cheetah Access
Enterprise Router
Accton Wireless
WiFi Router
Business Series
Managed Routers
Note: Accton uses 192.168.1.1 as primary IP. Cheetah Access model uses 192.168.2.1.
How to Login to Accton Router
Connect to Accton Network
Connect your device to Accton router via Ethernet cable (recommended for enterprise routers). For wireless models, connect to WiFi. Wired connection ensures stable access during configuration.
Open Browser & Enter IP Address
Open any web browser and type one of these IP addresses:
http://192.168.1.1http://192.168.2.1 (Cheetah Access)Most Accton routers use 192.168.1.1. Check model documentation if unsure.
Enter Default Login Credentials
Enter default Accton router credentials:
Most Common:
Username: root
Password: none (leave blank)
Alternative (Some Models):
Username: (blank)
Password: (blank)
Check router label on back/bottom for model-specific credentials.
Access Router Admin Panel
Successfully logged in! You'll see Accton router management interface. Configure network settings, VLANs, security policies, QoS, routing tables, and advanced enterprise features.
Enterprise Security
Immediately change default root password after first login. Use complex password with minimum 12 characters for enterprise security compliance.
Can't Access Accton Router? Troubleshooting
192.168.1.1 Not Loading
If login page won't open:
- • Verify Ethernet connection to LAN port (not WAN)
- • Try alternative IP:
192.168.2.1 - • Check computer is set to obtain IP automatically (DHCP)
- • Ping router: Open CMD → type
ping 192.168.1.1 - • Clear browser cache and cookies
- • Try different browser (Chrome, Firefox, Edge)
- • Disable proxy or VPN if active
- • Restart router: unplug 30 sec, plug back in
Wrong Password or Forgot Password
Try these default credentials:
• Username: root | Password: (blank/none)
• Username: (blank) | Password: (blank)
• Check router label or documentation for model-specific credentials
Forgot Custom Password? Perform 30-30-30 reset (hold RESET 30 sec while powered, 30 sec after unplug, 30 sec after plug back in). This is the hard reset method for enterprise routers.
Factory Reset Accton Router
- Ensure router is powered on
- Locate RESET button (small recessed hole)
- Use paperclip to press and hold RESET for 7-15 seconds
- Watch lights - release when they start flashing
- Wait 2-3 minutes for complete restart
- Login with default: root/(blank)
30-30-30 Hard Reset (Recommended for Accton): Hold RESET 30 seconds, unplug while holding 30 seconds, plug back in while holding 30 seconds. This ensures complete factory reset.
⚠️ Warning: Factory reset erases ALL configurations: VLANs, routing tables, security policies, firewall rules, and all custom settings. Document your configuration before reset.
Enterprise Configuration Features
Network Settings
- • VLAN configuration and management
- • Static and dynamic routing tables
- • DHCP server configuration
- • DNS settings and forwarders
- • Link aggregation (LACP)
Security
- • Access control lists (ACL)
- • Firewall rules and policies
- • Port security and 802.1X
- • VPN configuration (IPSec, SSL)
- • Authentication (RADIUS, TACACS+)
QoS & Performance
- • Quality of Service (QoS) policies
- • Bandwidth management
- • Traffic prioritization
- • Rate limiting
- • Network monitoring and SNMP
Management
- • Firmware updates
- • Configuration backup/restore
- • System logging and syslog
- • CLI access (Telnet/SSH)
- • SNMP monitoring
Frequently Asked Questions
What is the default password for Accton router?
Default username is root with password none (leave blank). Some models use blank username and blank password. Connect to router, open browser, go to 192.168.1.1, and enter credentials. Check router label for model-specific information.
What is Accton Cheetah Access router?
Accton Cheetah Access is an enterprise router model using 192.168.2.1 as default IP. Login with blank username and blank password. Popular for business networking with advanced routing and security features.
How do I reset Accton router password?
If you forgot password, perform 30-30-30 factory reset: Hold RESET button 30 seconds while powered, keep holding 30 seconds after unplugging, keep holding 30 seconds after plugging back in. This restores default root/(blank) credentials but erases all settings.
Why is 192.168.1.1 not accessible?
Common causes: wrong IP (try 192.168.2.1 for Cheetah), not connected to LAN port, computer not set to DHCP, firewall blocking. Check network adapter is set to obtain IP automatically. Ping router to verify connection. Restart router and computer if needed.